Flashlight UC35 + 18650 li-ion 3200 mAh akumulator - Fenix

The Fenix ​​UC35 rechargeable tactical flashlight is a rechargeable equivalent of the Fenix ​​PD35 flashlight. It is equipped with a Cree XM-L2 U2 diode and delivers a luminous flux of up to 960 lumens (ANSI) and an afterglow of up to 200 meters. The package also includes a rechargeable 18650 li-ion battery with a capacity of 3200 mAh, which is charged directly in the flashlight via a side micro-USB connector. Alternatively, the flashlight can be powered by two disposable CR123A batteries. The UC35 flashlight has six different lighting modes, which allow you to choose between high power and long life (up to 150 hours), there is also stroboscopic flashes for crisis situations. The lamp is powered by digitally regulated constant current to guarantee constant light output even when the voltage in the batteries is reduced (during their gradual discharge). The UC35 impresses not only with its small size and huge power, but also with the tactical switch and the possibility of attaching the AR102 or AER-02 cable switch. We can therefore also recommend it for use in security forces and for hunting.

• All lamp parameters (luminous flux, battery life, waterproofness, afterglow and impact resistance) are measured in accordance with the ANSI / NEMA FL 1-2009 standard.
• Parameters of the Fenix ​​UC35 lamp
• The high-performance Cree XM-L2 U2 LED with a lifespan of 50,000 hours is used.
• Six lighting modes: Turbo 960 lumens (1.5 hours) -> 480 lumens (2.75 hours) -> 180 lumens (9.25 hours) -> 50 lumens (38 hours) -> 14 lumens (150 hours) - Strobe (variable frequency strobe).
• Operation in Turbo mode 960 lumens is limited to 5 minutes at a time, then the flashlight automatically switches to 480 lumens mode.
• Luminous flux and endurance times are measured with the included li-ion 18650 battery with a capacity of 3200mAh (Fenix ​​ARB-L2P).
• Digitally controlled for constant brightness, low battery alert.
• A rechargeable Li-ion battery type 18650 can be purchased as a replacement battery.
• Alternatively, two disposable lithium batteries type CR123A can be used for power supply (do not try to recharge them in the flashlight).
• Protection against accidental battery insertion upside down (polarity reversal).
• Dimensions 15.0 cm (length) x 2.54 cm (diameter). Weight 99 grams (without batteries), 145 grams including battery.
• Made of aviation hardened aluminum type T6, durable surface - Type III hard anodized.
• Impact-resistant falls from a height of 1 meter. The flashlight has a memory and always switches on in the last set mode (does not apply to flash modes).
• Trapezoidal threads with increased wear resistance.
• Significant grooving of the surface for better grip, the design prevents the lamp from rotating on an uneven surface.
• Waterproof according to the IPX-8 standard (tested underwater at a depth of 2 meters).
• Removable steel clip with titanium finish.
• Hardened ultra clean glass lens with anti-reflex surface.
• Smooth parabolic reflector for light cone with afterglow of 200 meters (10000cd).
• Tactical switch at the end of the flashlight (instantaneous on / off function - momentary on / off).
• The flashlight includes a wrist strap, belt case, Fenix ​​ARB-L2P battery with a capacity of 3200 mAh, USB cable and spare o-rings.
• Optional accessories can be purchased for example: cable switch AR102, cable switch AER-02, red traffic cone AOT-S, diffuser AOD-S, red filter AOF-S, green filter AOF-S, blue filter AOF-SK
• The USB adapter can also be purchased separately to the electrical network and USB adapter to the car, bicycle holder, special Fenix ​​bicycle holder or bicycle helmet holder BikeBlock, mounting on a weapon rail, magnetic mounting.

Application:

From the factory, there may be a black insulating cap on the battery inside the lamp. Remove it from the battery before using it for the first time. To turn it on, press the switch located at the end of the lamp, to activate it immediately, press the button. You can switch between power modes at any time during operation by pressing the side button on the lamp head. To switch to stroboscopic mode, hold down the side button for about 1 second.

Charging - open the rubber cover of the charging connector on the side of the lamp and connect the included cable (micro USB connector), connect the other end to the computer or USB adapter to the mains or car. The limit switch must be switched on for charging! The side button lights up red during charging. When fully charged, it lights up green. Charging a fully discharged battery takes about 4.5 hours.

Low battery warning - the flashlight automatically switches to the lowest mode and flashes 3 times every five minutes.

Product reviews In the practical police test of the Policejnidenik.cz branch website, the UC35 passed with excellent results and the police officers themselves therefore recommend it. It is one of the ideal lamps for normal service performance. Be light, said Policista.cz and set out to test the UC35 model in the field. Judgment? "The difference between a professional flashlight and a toy is not how many lumens it has or how harsh it looks. The difference is that a professional flashlight will never leave you in the dark. “For the editor-in-chief of the specialized web magazine Krasajachtingu.cz Jaroslav Foršt, the UC35 flashlight is a small hard worker with respectable parameters.

Caution

Do not disassemble the sealed parts in the head of the lamp yourself, as this will invalidate the warranty. If the flashlight in your hand is not too hot, it can be switched back to higher power. When using disposable CR123A batteries, do not attempt to charge them in the flashlight. If the protective rubber rings appear damaged after prolonged use, replace them. The rings should also be lubricated to prevent rubber erosion. By following these rules, the flashlight will be properly protected against water.

If the flashlight flashes or does not light up, it may be one of the following reasons:

• The batteries are almost empty - replace them or charge the battery.
• The contacts inside the lamp are clogged - clean them with a sponge soaked in alcohol.
• The head, body or back of the lamp are loose - add lubricant to the sealing rings and tighten both the head and the end of the lamp firmly.